FREE Shipping on all orders!

Installation Guide

Embrace Whole Body Learning through Movement Maze’s Active Ability Solution

Indoor Stickers

Installation Guide

Equipment

  • Tape Measure and Small Ruler or soft tape measure
  • Broom and dustpan
  • Squeegee (provided)
  • Chalk
  • Spray bottle with water and a squirt of dish liquid
  • Carry bag to store the sticker backings
l

Preparation

  1. Lay the stickers out flat under a weight for a few hours to help with installation.
  2. Ensure Floors have been vacuumed for dirt, dust and hairs, and washed of any greasy substances before application. This is VERY IMPORTANT.
  3. Floor MUST BE DRY before application.
  4. Lay out all designs on the floor before application to ensure correct alignment, distances and placement as stickers ARE NOT MOVEABLE once applied. They can be removed and replaced but not moved.

Installation

5. Use the activity placement guides to assist with placement of order, distances and spacing.

6. Once happy with the placement of your stickers, place a small mark on the floor using the chalk under the bottom and top corner of each sticker to help with placement. DO THIS FOR ALL STICKERS in case something gets knocked or moved.

7. Start at the first sticker. Remove the backing of the sticker and discard into your carry bay.

8. Spray the back of the sticker with 1-2 squirts of soapy water. This will help with placement as it allows for slight adjustments when you lay the sticker down.

9. Turn the sticker over and line up the bottom of the sticker with the marking dot on the ground applied in step 6.

10. Put that corner of the sticker on the ground.

11. While holding the sticker with one hand, use the squeegee to apply the sticker with a sweeping motion from the middle towards the edge, removing air and water as you go.

12. Work your way towards your other hand.

13. If the sticker is moving as you do this, simply lift it up, blow on the back of the sticker to allow the water to dry and try again.

14. Repeat for all stickers.

}

Time Guide

Allow 2-3 hours to install a full kit (7 pieces). The longest part is the preparation and lining up of activities. Once you have done this, the installation is fairly quick once you get the hang of it.

Allow to “REST” for 6-8 hours before use and do not wash floors for 24 hours

Note: Do not try to peel back the stickers if you have bubbles, try to push the bubbles towards the edge or you can lightly pop the sticker with a fine needle to release the bubble if needed.

For further support please contact us.

Outdoor Stickers

Installation Guide

Equipment

  • Tape Measure and Small Ruler or soft tape measure
  • Broom and dustpan (Blower Vac makes for a quick job)
  • Paint Roller (Foam – firm 100mm)
  • Chalk
  • Carry bag to store the sticker backings
l

Preparation

  1. Lay the stickers out flat under a weight for a few hours to help with installation.
  2. Ensure Floors have been swept for dirt, dust and hairs, and washed of any greasy substances before application. This is VERY IMPORTANT.
  3. Floor MUST BE DRY before application.
  4. Lay out all designs on the floor before application to ensure correct alignment, distances and placement as stickers ARE NOT MOVEABLE once applied. They can be removed and replaced but not moved.

Installation

5. Use the activity placement guides to assist with placement of order, distances and spacing.

6. Once happy with the placement of your stickers, place a small mark on the floor using the chalk under the bottom and top corner of each sticker to help with placement. DO THIS FOR ALL STICKERS in case something gets knocked or moved.

7. Start at the first sticker. Remove the backing of the sticker and discard into your carry bay.

8. Turn the sticker over and line up the bottom of the sticker with the marking dot on the ground applied in step 6.

9. Put that corner of the sticker on the ground.

10. While holding the sticker with one hand (your non-writing hand), use the paint roller to apply the sticker from base to tip removing air as you go.

11. Work your way towards your other hand.

12. Once the whole sticker is down, run over the top of it with the roller to make sure the edges are stuck down to prevent stickers lifting.

}

Time Guide

Allow 2-3 hours to install a full kit (7 pieces). The longest part is the preparation and lining up of activities. Once you have done this, the installation is fairly quick once you get the hang of it.

Allow to “REST” for 6-8 hours before use and do not wash floors for 24 hours

Note: Do not try to peel back the stickers if you have bubbles, try to push the bubbles towards the edge or you can lightly pop the sticker with a fine needle to release the bubble if needed.

For further support please contact us.

Choose Movement Maze

Children need to learn to move
and they also need to move to learn

Movement Maze Logo

Designed by a Physiotherapist with experience working with children and people with disabilities. Endorsed by Allied Health Team of Occupational Therapists and Speech Therapists to optimize Multi-Sensory Learning Opportunities.

Ideal Uses

Schools

Creche

Daycares

Therapy Clinics

Airport Waiting Zones

Hospital Corridors